Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Opener Repair for Austin Homeowners
A gate opener that grinds, beeps, or refuses to move isn’t just a hassle – in Austin’s heat and humidity, it’s a security issue. For fast help, call our Austin Gate Opener Repair team. Calder Gate Repair Austin fixes that. We’re a dedicated gate repair specialist inside the Relay Home Co. family, founded in 2009, and we handle every major opener brand you’re likely to have bolted to your driveway. Our techs arrive in uniform with a live, trackable arrival time, not a vague four-hour window. Most repairs are completed same day because we stock common parts on the truck. If you’re dealing with a gate that won’t open, a keypad that’s dead, or an opener that screams every time it cycles, call (903) 354-7419 and get a live person, not a recording.
Gate Operator
A Gate Operator is the motor-and-gearbox unit that physically swings or slides your gate – everything else (remote, keypad, safety sensors) talks to it. When the operator itself fails, the gate either won’t move at all or moves in jerky, partial strokes. Calder Gate Repair Austin replaces capacitors, control boards, limit switches, and entire operator units across LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most operator repairs run $220 – $360 before parts, and full operator replacement with a new unit typically starts around $480 – $800 depending on swing vs. slide and horsepower. Every job gets a written price before any work starts, and it’s backed by the 365-Day Done Right Promise.
Limit Switch Failure
Limit switches are the small sensors that tell the gate when to stop. When they wear out or drift out of alignment, the gate over-travels and slams into the post or stops six inches short of closed. We test and recalibrate them on every service call.
Capacitor Burnout
In Austin’s summer heat, capacitors cook. The symptom is a hum followed by nothing – the motor tries to start and can’t. We replace capacitors on the spot from truck stock, usually for under $100 parts cost.
Styles & brands we work with
Electric Gate Closers
Electric Gate Closers are the mechanism – typically a hydraulic arm or heavy spring assembly – that pulls the gate shut after it opens. They work with the operator, not instead of it. When the closer fails, the gate drifts open after every cycle or slams shut hard enough to rattle hinges. Calder Gate Repair Austin diagnoses and services closers on most brands, including hydraulic and mechanical units, with typical repair costs running $160 – $280. We check closer flush rate, spring tension, and mounting hardware as part of any gate servicing visit, because a bad closer will destroy a good operator over time.
Drifting Gate Panels
If your gate stops short of full close or hangs open after the operator releases, the closer has lost pressure or spring tension. This is a safety issue more than a convenience one – a gate that won’t seal is an invitation.
Slamming on Close
The opposite failure. The closer’s damping is gone, so the gate accelerates and hits the stop hard enough to damage hinges, welds, and the operator’s gears. We adjust or rebuild the closer before it takes the whole system out.
Gate Servicing
Gate Servicing is scheduled preventive maintenance – the oil change for your gate, done before something fails. Calder Gate Repair Austin offers it as a tune-up package that covers the operator, closer, hinges, wheels (on slide gates), safety edges, photo eyes, and battery backup. We charge $180 – $260 for a full service visit, which includes lubrication, cleaning, torque checks, and a written condition report so you know what’s wearing and what can wait. Most Austin homeowners schedule gate servicing once every 12 – 18 months, although gates on steep driveways or heavy traffic get it twice a year. It extends the life of the operator and catches failures before they become emergency calls.
Scheduled Tune-Up Package
We go through the entire system: chain or belt tension, gearbox oil, limit switch alignment, safety sensor alignment, remote programming, and battery health. You get a written report with photos of anything that’s wearing.
Pre-Season Storm Prep
Before Austin’s spring storm season and summer heat, we make sure the operator is sealed, the battery backup holds a charge, and the safety edges respond. It’s peace of mind without the markup of an emergency dispatch.
Gate Intercom
A Gate Intercom is the call box at the driveway – the thing a visitor pushes to buzz your phone, a wall unit, or a hands-free app. Most Austin gate intercoms are either hardwired phone-line systems, cellular units, or Wi-Fi video intercoms. Calder Gate Repair Austin repairs and replaces call buttons, speaker/mic modules, transformers, wiring, and full intercom kits, with typical repair costs ranging from $140 – $300 before parts, depending on whether we’re re-soldering a connection, replacing a handset, or converting a dead phone-line unit to cellular. We also sync intercoms with the gate operator so the open command actually fires.
No Audio or Dead Keypad
Symptom: the visitor presses the button, you hear nothing, or the keypad won’t take codes. Often it’s a degraded transformer or corroded wire in the pedestal. We test each leg of the circuit and replace the failed component.
Cellular Conversion
If your landline is gone or the copper line is fried, we convert the intercom to a cellular unit that calls your cell phone directly. You keep the existing pedestal and wiring; we swap the communications module and reprogram it.
Gate Opener With Keypad
A Gate Opener With Keypad is the access system that lets you punch in a code instead of carrying a remote – and in Austin, most modern installs include it. When the keypad stops accepting codes, eats batteries, or won’t fire the operator, Calder Gate Repair Austin troubleshoots the keypad, the wiring run to the operator, and the operator’s receiver board. Typical keypad repairs run $120 – $220, including re-terminating connections, replacing the keypad membrane, or reprogramming the control board. A full keypad replacement, including a weatherproof unit rated for Texas sun, usually lands in the $200 – $350 range installed.
Water Ingress in Austin Storms
Keypads on pedestals take direct hits from rain and afternoon heat. Corroded contact pads and swollen membranes are the most common failure we see across Austin neighborhoods like Hyde Park and Allandale. We seal the replacement properly so it survives.
Code Programming and Security
If a code was shared with a contractor, ex, or house sitter, we re-program the keypad and purge old codes so only the ones you want still work. We also set temporary codes for guests or deliveries that expire on their own.
Brands We Service
We’re factory-familiar with nine major brands, and that matters when your opener is three years old and discontinued. Ghost Controls units are popular on residential swing gates in the Austin area, and we’ve replaced enough of their control boards to know the exact failure patterns. DoorKing is common in gated communities across Travis County, and their heavier commercial units demand careful calibration we do routinely.
We also work on Elite slide operators – which are everywhere on Austin’s long driveways in the hills – and Mighty Mule, a brand we see on a lot of DIY installs that never got wired or programmed correctly. Whether you have Ghost Controls, DoorKing, Elite, Mighty Mule, or any other make, we can diagnose it, quote it, and fix it.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Gate won’t open or close all the way. The operator starts, then stops mid-travel or reverses before the gate is seated. That’s usually a limit switch or safety sensor fault, and it leaves your property partially open. We can fix it same day in most Austin neighborhoods.
- Loud grinding or banging during travel. A healthy gate operator runs with a steady hum. Grinding means a gearbox or chain sprocket is failing; banging means a wheel, hinge, or track is binding. Continuing to run the gate does more damage with every cycle.
- Opener hums but gate doesn’t move. That’s a failed capacitor, and in Austin heat it’s the single most common cause we respond to. The capacitor is inexpensive; running the motor against a failed capacitor is not. Shut the gate off at the breaker and call us.
- Remote works, keypad doesn’t (or vice versa). If one access method works and the other doesn’t, the problem is in the receiver, keypad wiring, or the programming – not the motor. It’s a fast fix most of the time, but it needs a tech with the right diagnostic tools.
- Battery backup beeping or dead. If your gate has a battery backup and it’s chirping or showing a fault, it won’t hold the gate through the next power outage. Austin storms knock out power regularly; a dead backup means a gate that’s locked open or closed with no way to move it.
Our Process, Step by Step
- 1
Book the call with a live person. You call (903) 354-7419, a human answers – 24 hours a day, every day – and logs your address, symptoms, and the make and model of your opener. We give you a live, trackable arrival time, not a four-hour window.
- 2
We arrive, test, and diagnose. The tech pulls up in uniform, walks the gate, and uses a multimeter to check voltage to the operator, the control board, the capacitor, and the safety sensors. We check the operator’s amp draw against spec and manually cycle the gate to feel for mechanical binding.
- 3
We quote a written price before any work starts. You get the number on paper before a single bolt is turned. The total on the invoice is the number you agreed to at the door – always. No parts get ordered and no repairs start without your ok.
- 4
We fix it and prove it. The repair is done with OEM or matching-spec parts, then we cycle the gate 20 to 30 times and re-test every safety device. We photograph before-and-after work, and you receive a digital invoice you can pay from a link.
- 5
You’re covered for 365 days. Every repair carries the 365-Day Done Right Promise, in writing. If the repair fails within that year, Calder Gate Repair Austin returns at no charge. That’s the whole promise, stated plain.
How Much Does Gate Opener Repair Cost in Austin?
Most gate opener repairs in Austin land between $180 and $360 before parts, with the most common fixes – capacitors, limit switches, and keypad wiring – typically running $120 – $250 all-in. We also cover nearby communities with our Gate Opener Repair in Manor service. A full operator replacement, which is sometimes the right call when a 12-year-old unit has already been repaired three times, starts around $480 and can run to $800+ depending on horsepower, swing versus slide, and whether you need a new battery backup. The single biggest price variable is whether we’re fixing a worn part or replacing a dead unit. Parts availability follows brand and age – a newer LiftMaster or Ghost Controls board is easy, a 15-year-old off-brand operator sometimes means custom sourcing.
What affects your price: the type of gate (slide gates cost more to diagnose because there’s more track and wheel work), the access (steep driveways in areas like Westlake or Cat Mountain add labor), and whether the failure is electrical or mechanical. South of the city? We also provide Buda Gate Opener Repair. What we don’t do is pad the quote. You get one written price, agreed before work starts, and it doesn’t change at the door. The free estimate includes the diagnostic visit and the written quote – no obligation.
Our Service Area Near Austin
Calder Gate Repair Austin is based in Austin and dispatches to surrounding communities including Georgetown, Kyle, Lakeway, Taylor, Lago Vista, Jollyville, Wells Branch, Lost Creek, Hornsby Bend, Shady Hollow, and Buda. Typical response times are same day for most Austin neighborhoods and next day for outlying areas. If you’re in Georgetown, visit our Gate Opener Repair in Georgetown page. In Kyle, see Gate Opener Repair in Kyle for service specifics. From home, use the navigation to reach both.
Serving Austin, TX - Our Local Coverage Area
We’re based in the Austin area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Opener Repair in Austin
Gate opener repair is the diagnosis and correction of failures in the motor, control board, gearbox, and access devices that operate an automatic driveway gate. Calder Gate Repair Austin handles the full system – operator, closer, safety edges, intercom, keypad, and battery backup. Common repairs include capacitor replacement, limit switch alignment, control board replacement, and keypad re-wiring. Every repair carries a written price before work starts and the 365-Day Done Right Promise.
Most repairs are completed same day, usually within one to two hours on site. The exception is when a control board or motor has to be ordered, which can add two to five business days. We stock common parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule on the truck, so the fix often happens on the first visit. If a part is on order, we leave the gate in the safest possible configuration until we return to finish.
Most repairs run $180 – $360 before parts, and the most common single-component fixes – capacitors, limit switches, keypad repairs – land between $120 and $250 total. Full operator replacement starts around $480 depending on the unit. You’ll get a written price before any work starts, and the number doesn’t change at the door. Call (903) 354-7419 for an exact quote – estimates are free.
Yes, LiftMaster is one of the nine brands we’re factory-familiar with, and it’s one of the most common openers we see on Austin homes. We repair LiftMaster swing and slide operators, replace their control boards, capacitors, and limit switches, and we stock common LiftMaster parts on the service trucks. If your LiftMaster is the offender, call (903) 354-7419 for a same-day diagnosis.
Yes, a live person answers our phone 24 hours a day, 7 days a week, and we dispatch for emergency calls – gates that won’t close and can’t be secured, or gates that won’t open and trap a vehicle in. Emergency dispatch in the middle of the night is available; during regular business hours, most Austin repairs are done same day. Call (903) 354-7419 and a real human will book you in.
Every repair carries the 365-Day Done Right Promise in writing. If the repair fails within 365 days, Calder Gate Repair Austin returns at no charge to make it right. There’s no fine print about partial coverage – it’s a full year, in writing, on every job. That includes parts and labor for the specific repair we performed.
Clear any debris away from the gate track and hinges, and if possible, park vehicles clear of the gate’s full swing or slide path. Have the make and model of your opener handy if you know it – there’s usually a label on the motor housing – though our techs identify virtually every unit on arrival. Keep the gate in its current state; don’t force it open or closed before we arrive. If it’s an emergency and the gate is stuck open, we’ll prioritize securing it first.
Schedule Your Gate Opener Repair Service in Austin Today
A gate that won’t behave is a problem that only gets more expensive as you keep forcing it. Call (903) 354-7419 and talk to a live person who can book your repair, give you a same-day arrival window, and answer questions about cost before you commit. The estimate is free, the price is written before any work starts, and every repair is backed by the 365-Day Done Right Promise. Calder Gate Repair Austin – part of the Relay Home Co. family since 2009.